Not so nice 
Pinasco «Slave» engine case with crankshaft (43 mm stroke / 12 mm KoBo) and double intake suitable for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The Pinasco «Power Casing» engine housing is supplied with a crankshaft specially developed for this purpose, which has a wide cheek for controlling the intake.
A standard 13 mm Dellorto SHA carburettor can be fitted to the rear of this housing, as well as any side-mounted carburettor with a 24 mm connection on the diaphragm system. The frame may have to be adapted in this case.
With this dual carburetor system, you can tease the last bit of horsepower out of your racing car.
The following parts are included in the scope of delivery:
- Rear intake flange (connection diameter: 16 mm, Ø-inside: 13 mm)
- Side membrane system incl. sealing plug for the 13 mm flange if this is not used
- Mounting material for diaphragm flange (connection diameter: 24 mm, Ø inside: 20 mm)
- Cylinder stud bolt
- Engine housing (Ø for cylinder neck up to 50.7 mm)
- Engine housing screws
- Crankshaft Pinasco Competition with 43 mm stroke and 12 mm piston pin (axe 12)
- Installation instructions in English & Italian
No housing seal is supplied. Sealing compound is used for sealing
We recommend using the 46 mm Pinasco cylinder kit for this racing gear. In addition, only electronic ignitions can be fitted to this housing.
If the engine is installed in a Piaggio Ciao frame, some material must be removed from the right-hand side of the housing and cylinder. This process is described in the installation instructions.
Corresponding add-on parts such as sealant, racing kit, racing ignition etc. can be found in the accessories section.
Mäsig-läsig! – We strive to offer you the widest range of moped spare parts. However, this product is of rather poor quality and is not recommended by us. Should you nevertheless choose this item, we understand, but cannot offer you any guarantee or exchange.
Quality product from the Italian manufacturer Pinasco.
| Manufacturer | Pinasco |
| Material | Aluminum |
| Crankshaft stroke | 43 mm |
| Ignition type | Electronic |
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Ratings
Accessories & related products
Dell'Orto 19 mm PHBG CS carburetor hand choke
Manufacturer: Dell'Orto · Material: Aluminum · Component group Carburetor: Carburetor complete · Carburetor type: PHBG CS · Nominal diameter: 19 mm · Choke control: Hand choke · Color: black · Width: 70 mm · Nozzle thread: M5x0.8 (standard thread) · Ø fuel hose connection: 5.4 mm · Ø fuel hose connection: 6 mm · Total length: 82 mm · Height: 124 mm · Ø without reducing sleeve: 26 mm · Nozzle size: 75 · Mounting type: Plug connection clamped · Ø Inside entrance: 19 mm · Ø Internal connection: 24 mm · Ø Output inside: 19 mm · Ø Air filter connection: 32 mm · Ø Air filter connection: 60 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Mixed oil connection: Yes · Vacuum connection: Yes · Area of application: Racing · Area of application: Tuning · Choke nozzle size: 60 · Camouflaged: No · Size of secondary nozzle: 45
EUR 148.60
Malossi racing ignition 12V | Piaggio Ciao, SI, Bravo, Boxer
Number of fixing points: 2 pcs · Manufacturer: Malossi · Material: Steel · Ø Internal flywheel: 80.5 mm · Light coil voltage: 12 V · Direction of rotation: right · Weight: 804 g · Weight: 890 g · Performance: 90 W · Mounting type: Screws · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 139.5 mm · Ø cable: 7 mm · Area of application: High End · Area of application: Performance · Area of application: Racing · Area of application: Tuning
EUR 495.50
SKF 6202 C3 ball bearing 15/35/11
Bearing cage: Sheet steel cage ball-guided · Inner ring width: 11 mm · Manufacturer: SKF · Bearing clearance: C3 · Stock number: 6202 · Bearing type: Deep groove ball bearing · Width: 11 mm · Ø inside: 15 mm · Ø outside: 35 mm · Puch OEM number: 900.4.6202
EUR 12.30
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Manufacturer: Elring · Material: Silicone · Contents: 70 ml · Color: gray · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Gap dimension (max.): 2 mm · Temperature resistance (min.): -60 - 315 °C · Area of application: Chemistry
EUR 24.70
EUR 352.86/l
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Pinasco · Material: Aluminum · Material: Carbon · Surface: varnished · Ø Internal flywheel: 106 mm · Direction of rotation: right · Weight: 650 g · Height: 38.7 mm · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Thread length: 7.5 mm · Cone length: 12.5 mm · Cone ratio: 1:5 · Thread type: MF16x1 (fine pitch thread)
EUR 260.10
Dell'Orto 13/13 SHA carburetor hand choke | Piaggio Ciao P, SC
Nominal diameter: 13 mm · Manufacturer: Dell'Orto · Area of application: Tuning · Component group Carburetor: Carburetor complete · Material: Aluminum · Carburetor type: SHA (Piaggio) · Choke control: Hand choke · Total length: 55 mm · Width: 60 mm · Color: black · Height: 110 mm · Nozzle thread: M5x0.8 (standard thread) · Mounting type: Plug connection clamped · Ø fuel hose connection: 5.2 mm · Ø fuel hose connection: 6 mm · Ø without reducing sleeve: 18 mm · Nozzle size: 66 · Ø Inside entrance: 13 mm · Ø Internal connection: 16 mm · Ø Output inside: 13 mm · Ø Air filter connection: 50.9 mm · Mixed oil connection: No · Vacuum connection: No · Camouflaged: No
EUR 86.60
Malossi oil seal FPM 15/24/5 A crankshaft | Piaggio Ciao, SI, Bravo, Boxer
Temperature resistance (min.): -30 - 200 °C · Shaft seal type: A - With rubberized outer part / one sealing lip. · Manufacturer: Malossi · Material: FPM / FKM (colloquially known as Viton) · Surface: rubberized · Place of use: Crankshaft · Width: 5 mm · Ø inside: 15 mm · Ø outside: 24 mm
EUR 17.70
Pinasco 46 mm cylinder kit EVOTEN BIG 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Nominal diameter: 46 mm · Manufacturer: Pinasco · Material: Aluminum · Area of application: Tuning · Surface: varnished · Displacement: 71 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 49.9 mm · Ø Outlet outside: 22.5 mm · Ø Outlet outside: 25 mm · Ø Outlet outside: 28 mm · Ø outlet inside: 18.5 mm · Ø outlet inside: 20.9 mm · Ø outlet inside: 24.4 mm · Number of fixing points: 3 pcs · Ø piston pin (B): 12 mm · Hole spacing outlet: 47.5 mm · Outlet type: clamped · Outlet type: slanted · Thread outlet: M6x1 (standard thread) · Hole pattern [mm]: 55 x 34 · Decompressor: Yes · Camouflaged: No
EUR 520.30
Pinasco 46 mm cylinder kit EVOTEN 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Nominal diameter: 46 mm · Manufacturer: Pinasco · Material: Aluminum · Area of application: Tuning · Surface: varnished · Displacement: 71 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 50 mm · Ø Outlet outside: 22.5 mm · Ø outlet inside: 18.5 mm · Number of fixing points: 3 pcs · Ø piston pin (B): 12 mm · Hole spacing outlet: 48 mm · Outlet type: clamped · Outlet type: slanted · Thread outlet: M6x1 (standard thread) · Hole pattern [mm]: 55 x 34 · Decompressor: Yes · Camouflaged: No
EUR 470.70
Moped fans also bought
WEKEM 2K liquid metal
Manufacturer: WEKEM · Material to be used: Aluminum · Material to be used: Ceramics · Material to be used: Metal · Material to be used: Steel · Material to be used: Wood · Contents: 24 ml · Color: gray · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Hazard warning: May cause allergic skin reactions · Hazard warning: Toxic to aquatic organisms (with long-term effects) · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous · Hazard pictogram: GHS09 - Hazardous to the aquatic environment · Temperature resistance (min.): -20 - 80 °C · Type of application: 2K · Alignment time: 240 sec · Area of application: Chemistry
EUR 24.70
EUR 494.00/kg
Collection only possible with online purchase and appointment.
