High-quality M12x185 mm thru axle for your Puch moped / moped with LELEU or Grimeca wheel hub in the rear 5-spoke rim.
The rear wheel axle includes all required washers, nuts and spacers.
The cable ties show you where the individual parts should be fitted.
- Red cable tie: hub
- Blue cable ties: swingarm
- green cable tie: brake anchor plate
Notes: This wheel axle is not suitable for Snowflake cast rims.
Complete wheel axle sets with the corresponding industrial bearings can be found in the accessories section.
Nostalgic product for the highest demands of the quality brand swiing®.
| Manufacturer | swiing® revival parts |
| Material | Steel |
| Surface | galvanized (blue) |
| Ø shaft | 11.9 mm |
| Shank length | 100 mm |
| Ø outside | 11.8 mm |
| Total length | 185 mm |
| Width across flats | 19 mm |
| Thread type | MF12x1 (fine pitch thread) |
| Thread length | 26 mm, 52.5 mm |
| Puch |
Ratings
Accessories & related products
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 28 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ball bearing closed: Yes
EUR 38.00
swiing® ingenious wheel axle with bearing conversion kit Snowflake rear wheel | Puch Maxi
Manufacturer: swiing® ingenious parts · Material: Chrome steel (colloquially known as stainless steel) · Material: Steel · Surface: galvanized (blue) · Total length: 185 mm · Thread type: MF12x1 (fine pitch thread) · Ball bearing closed: Yes
EUR 73.60
Not in stock
Moped fans also bought
GPO sprocket 45 teeth black | Puch Maxi, Puch X30 NG-2AH
Chain pitch: 1/2" x 3/16" · Chain type: 415H · Manufacturer: GPO · Material: Steel · Color: black · Surface: powder-coated · Ø mounting hole: 6.7 mm · Number of teeth: 45 pcs · Ø inside: 94 mm · Ø bolt circle: 105.5 mm · Thickness: 4.5 mm · Hole spacing 2: 68 mm · Cranking (offset): 8 mm · Number of fixing points: 6 pcs · Hole spacing: 36.5 mm
EUR 24.50
NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi
Bearing cage: Sheet steel cage ball-guided · Stock number: 6001 · Inner ring width: 12 mm · Manufacturer: NTN · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Bearing type: Deep groove ball bearing · Width: 8 mm · Ø inside: 12 mm · Ø outside: 28 mm · Ball bearing closed: Yes · Area of application: Standard
EUR 7.25
Cast wheel hub | Puch Maxi, X30 NG-2AH
Material: Aluminum · Surface: blank · Surface: raw · Color: silver · Ø mounting hole: 6.1 mm · Ø inside: 27.9 mm · Ø bolt circle: 105 mm · Ø axle: 12 mm · Ø outside: 114.7 mm · Total length: 105 mm · Ø drum: 80 mm · Thread type: FG34.8 (1.37" 24G) · Number of fixing points: 12 pcs · Thread length: 12 mm · Area of application: Tuning
EUR 110.50
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 28 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ball bearing closed: Yes
EUR 38.00
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Ø bore: 12.2 mm · Ø axle: 12 mm · Ø outside: 91 mm · Ø screw holder: 6.5 mm · Total length: 187 mm · Wide cam holder: 12 mm · Cranking (offset): 8 mm · Brake lever length (lever length): 55 mm
EUR 85.90
swiing® ingenious wheel axle with bearing conversion kit cast hub front | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 11.95 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 34.5 mm · Shank length: 74.5 mm · Height: 5.9 mm · Height: 9.9 mm · Ø inside: 12 mm · Ø outside: 29.02 mm · Total length: 165 mm · Width across flats: 19 mm · Thread type: MF12x1 (fine pitch thread) · Ball bearing closed: Yes · Thread length: 40.5 mm · Thread length: 50 mm
EUR 47.80
Collection only possible with online purchase and appointment.
