Copy of the KTM SX50 clutch suitable for all Puch Maxi mopeds / mopeds with E50 engine.
Attention: The clutch hub does not fit Puch Maxi crankshafts as the cone is not correct.
The cone can either be reworked or alternatively the high-quality matching MBR clutch star, which is listed under accessories, can be used.
Tightening torque on crankshaft: 35 - 40 Nm
Tightening torque screws for jaws: 10 Nm
The fastening nut is not included in the scope of delivery.
Mäsig-läsig! – We strive to offer you the widest range of moped spare parts. However, this product is of rather poor quality and is not recommended by us. Should you nevertheless choose this item, we understand, but cannot offer you any guarantee or exchange.
The clutch is a cheap replica, the clutch linings therefore last less than the original KTM linings. During tests in our racing team, the clutch usually lasted between 1 and 2 hours, after which the linings had to be replaced. The star, the springs and also the fastening screws are advantageously used from the original KTM clutch.
High-quality alternatives can be found in the accessories section.
| Number of jaws | 3 pcs |
| Recording type | Cone mounting |
| Area of application | Tuning |
| Puch | E50 |
Accessories & related products
MBR Clutch KTM SX50 | Puch E50
Manufacturer: MBR · Material: Steel · Material addition: Aluminum · Recording type: Cone mounting · Number of jaws: 3 pcs · Number of springs: 3 pcs · Area of application: High End · Area of application: MX · Area of application: Racing · Area of application: Tuning
EUR 418.30
Explore categories from Clutch
Moped fans also bought
GPO Gasket Set for E50 Engine | Puch Maxi S, N
Manufacturer: GPO · Material: Aluminum · Material: Fiber · Material: Sealing carton · Material: Sealing paper · Area of application: Standard · Number of components: 7 pcs · Ø outlet inside: 19.9 mm · Hole spacing inlet: 32 - 38 mm · Hole spacing outlet: 42 mm · Decompressor: Yes · Hole pattern [mm]: 44 x 44
EUR 12.20
Rito Crankshaft Racing | Puch E50
Manufacturer: Rito · Material: Steel · Cheek type: Full cheeks · Crankshaft stroke: 43 mm · Weight: 970 g · Thread type: MF10x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 67 mm · Ø crank webs: 69.9 mm · Ø piston pin (B): 12 mm · Area of application: Racing · Area of application: Tuning · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread length: 11 mm · Thread length: 14 mm · Dimension needle bearing: 12 / 15 x 15 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Number of gears: 1 pcs
EUR 188.20
BOSCH screw-in condenser | Bosch / Ducati
Manufacturer: BOSCH · Capacity: 0.2 µF · Ø outside: 18 mm · Thread type: M3x0.5 (standard thread) · Mounting type: Plug connection clamped · Connection type: Thread for screwing · Height: 27 mm · Total height: 33.5 mm · Area of application: Original · Area of application: Standard · Alternative version of the Pony OEM number: A2090 · Pony OEM number: A2092 · BOSCH OEM number: 2 207 330 050 · Alternative version of the Sachs OEM number: 0265 052 003 · Sachs OEM no.: 0265 052 007
EUR 24.50
Hot 
BOSCH breaker with cable | Bosch / Ducati
Manufacturer: BOSCH · Material: Steel · Ø Internal flywheel: 90 mm · Cable length: 100 mm · Cable available: Yes · Ø axle: 4 mm · Ø mounting hole: 4.5 mm · Number of fixing points: 1 pcs · Alternative version of the Pony OEM number: A4606 · Alternative version of the Pony OEM number: A4606A · Pony OEM number: A4607 · BOSCH OEM number: 1 217 013 025 · Sachs OEM no.: 0283 116 102 · Alternative version of the Sachs OEM number: 0983 106 000 · Alternative version of the Sachs OEM number: 2783 039 001 · BERU OEM number: 0 340 100 710
EUR 24.50
swiing® revival nut / spring washer clutch E50 | Puch Maxi
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Nut type: Hexagon nut 0.8D · Height: 8 mm · Drive: External hexagon · Nominal diameter (thread): 10 mm · Thread type: MF10x1 (fine pitch thread) · Width across flats: 17 mm
EUR 4.80
Hot
DUCATI ignition coil (1A quality)
Height: 17 mm · Manufacturer: DUCATI · Ø cable holder: 5.9 mm · Hole spacing: 54 mm · Place of use: Internal (in the ignition) · Color: black · Number of fixing points: 2 pcs · Ø Internal flywheel: 90 mm · Ø mounting hole: 4.6 mm · Cable length: 37 mm · Area of application: Original · Area of application: Standard · Total length: 76.5 mm · Mounting type: Screws · Pony OEM number: A2114 · Alternative version of the Pony OEM number: A2116 · Alternative version of the Pony OEM number: A2118 · Pony OEM number: A5524 · Alternative version of the Sachs OEM number: 0265 142 002 · Alternative version of the Sachs OEM number: 0265 142 004 · Sachs OEM no.: 0265 132 100 · Sachs OEM no.: 0265 203 001
EUR 122.90
Not in stock
swiing® ingenious crankshaft "High End" | Tomos Classic, Quadro, Sprint, Fun Sport'R
Manufacturer: swiing® ingenious parts · Cheek type: Full cheeks · Thread type: MF10x1 (fine pitch thread) · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 93 mm · Total length crankpin ignition side: 64 mm · Ø crank webs: 70 mm · Ø piston pin (B): 12 mm · Area of application: Racing · Wide crank webs: 34 mm · Tomos OEM number: 223421
EUR 166.00
Not in stock
Working late? Evening hours on Thursday until 20:00
