Pinasco “Slave” engine casing with crankshaft (43 mm stroke / 12 mm bore) and dual intake, compatible with your Piaggio Ciao, Si, Bravo, Boxer, and Grillo moped.
The Pinasco “Power Casing” engine casing comes with a specially designed crankshaft that features a wider flange for controlling the intake at the rear intake port.
On this casing, you can install either a standard 13 mm Dellorto SHA carburetor at the rear or any side-mounted carburetor with a 24 mm connection on the diaphragm system. The frame may need to be modified for this.
With this twin-carburetor system, you can squeeze every last horsepower out of your race car.
The following parts are included in the package:
- Rear intake flange (16 mm connection, 13 mm inner diameter)
- Side-mounted diaphragm system, including a plug for the 13 mm flange if it is not being used.
- Mounting hardware for diaphragm flange (24 mm connection, 20 mm inner diameter)
- Cylinder studs
- Motor housing (for cylinder necks with an outer diameter up to 46 mm)
- Engine block bolts
- Pinasco Competition crankshaft with 43 mm stroke and 12 mm piston pins (axe 12)
- Installation instructions in English and Italian
No crankcase gasket is included. Sealant must be used for sealing.
For this racing crankcase, we recommend using the 42 mm Pinasco cylinder kit. Additionally, only electronic ignition systems can be installed on this crankcase.
If the engine is installed in a Piaggio Ciao frame, some material must be removed from the right side of the housing and cylinder; this is described in the assembly instructions.
You’ll find the necessary accessories—such as sealant, racing kits, racing ignition systems, etc.—in the accessories section.
So-so! – We strive to offer you the widest selection of moped replacement parts. However, the quality of this product is rather so-so, and we do not recommend it. If you still decide to go with this item, we understand your choice, but we cannot offer any warranty or accept returns.
Manufactured by the Italian brand Pinasco.
| Manufacturer | Pinasco |
| Material | Aluminum |
| Crankshaft stroke | 43 mm |
| Ignition type | Electronic |
| Piaggio | Ciao - P , SC , PX , C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
Dell'Orto 19 mm PHBG CS carburetor hand choke
Manufacturer: Dell'Orto · Material: Aluminum · Camouflaged: No · Component group Carburetor: Carburetor complete · Color: black · Nominal diameter: 19 mm · Choke control: Hand choke · Carburetor type: PHBG CS · Nozzle thread: M5x0.8 (standard thread) · Ø fuel hose connection: 5.4 mm · Ø fuel hose connection: 6 mm · Total length: 82 mm · Ø without reducing sleeve: 26 mm · Width: 70 mm · Nozzle size: 75 · Area of application: Racing · Area of application: Tuning · Ø Inside entrance: 19 mm · Mounting type: Plug connection clamped · Ø Output inside: 19 mm · Height: 124 mm · Ø Air filter connection: 32 mm · Ø Air filter connection: 60 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Ø Internal connection: 24 mm · Mixed oil connection: Yes · Vacuum connection: Yes · Choke nozzle size: 60 · Size of secondary nozzle: 45
EUR 147.60
Malossi racing ignition 12V | Piaggio Ciao, SI, Bravo, Boxer
Material: Steel · Manufacturer: Malossi · Mounting type: Screws · Number of fixing points: 2 pcs · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Ø Internal flywheel: 80.5 mm · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 139.5 mm · Ø cable: 7 mm · Weight: 804 g · Weight: 890 g · Area of application: High End · Area of application: Performance · Area of application: Racing · Area of application: Tuning
EUR 492.10
SKF 6202 C3 ball bearing 15/35/11
Manufacturer: SKF · Bearing type: Deep groove ball bearing · Stock number: 6202 · Width: 11 mm · Inner ring width: 11 mm · Bearing clearance: C3 · Bearing cage: Sheet steel cage ball-guided · Ø inside: 15 mm · Ø outside: 35 mm · Puch OEM number: 900.4.6202
EUR 12.20
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Manufacturer: Elring · Area of application: Chemistry · Material: Silicone · Color: gray · Contents: 70 ml · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Gap dimension (max.): 2 mm · Temperature resistance (min.): -60 - 315 °C
EUR 24.50
EUR 350.00/l
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Pinasco · Material: Aluminum · Material: Carbon · Surface: varnished · Thread type: MF16x1 (fine pitch thread) · Direction of rotation: right · Weight: 650 g · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Cone length: 12.5 mm · Cone ratio: 1:5 · Ø Internal flywheel: 106 mm · Ø Flywheel outside: 135 mm · Thread length: 7.5 mm · Height: 38.7 mm
EUR 258.30
Dell'Orto 13/13 SHA carburetor hand choke | Piaggio Ciao P, SC
Manufacturer: Dell'Orto · Camouflaged: No · Component group Carburetor: Carburetor complete · Material: Aluminum · Color: black · Carburetor type: SHA (Piaggio) · Nominal diameter: 13 mm · Ø Internal connection: 16 mm · Ø without reducing sleeve: 18 mm · Ø Inside entrance: 13 mm · Ø Output inside: 13 mm · Ø Air filter connection: 50.9 mm · Ø fuel hose connection: 5.2 mm · Ø fuel hose connection: 6 mm · Mixed oil connection: No · Vacuum connection: No · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Nozzle size: 66 · Mounting type: Plug connection clamped · Total length: 55 mm · Width: 60 mm · Height: 110 mm · Area of application: Tuning
EUR 86.00
Not in stock
Malossi oil seal FPM 15/24/5 A crankshaft | Piaggio Ciao, SI, Bravo, Boxer
Place of use: Crankshaft · Temperature resistance (min.): -30 - 200 °C · Shaft seal type: A - With rubberized outer part / one sealing lip. · Width: 5 mm · Ø inside: 15 mm · Ø outside: 24 mm · Manufacturer: Malossi · Material: FPM / FKM (colloquially known as Viton)
EUR 17.60
Pinasco 42 mm cylinder kit EVOTEN 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Nominal diameter: 42 mm · Manufacturer: Pinasco · Material: Aluminum · Surface: varnished · Displacement: 60 ccm · Crankshaft stroke: 43 mm · Ø Outlet outside: 22.5 mm · Ø piston pin (B): 12 mm · Outlet type: clamped · Number of fixing points: 3 pcs · Decompressor: Yes · Camouflaged: No · Area of application: Tuning
EUR 455.20
EUR 362.90
Explore categories from Gearbox & housing (motor)
Moped fans also bought
Working late? Evening hours on Thursday until 20:00
