Replica wire spoke hub made of aluminum with pressed-in bearings for the rear wheel of various mopeds, mopeds and small motorcycles.
Note: The hub is at the limit of tolerances in the area of the brake drum and sprocket mount. The function is just about guaranteed, but you shouldn't expect too much.
The bearings installed are also not of particularly high quality.
You can find suitable add-on parts for the rear hub such as brake pads, clamping screws etc. in the accessories section.
| Material | Aluminum |
| Surface | blank |
| Area of application | Standard, Custom |
| Ø Receptacle | 93 mm |
| Ø axle | 12 mm |
| Ø inside | 30 mm |
| Ø drum | 80 mm |
| Number of spoke holes | 36 pcs |
| Puch |
Ratings
Accessories & related products
- 12 %
Hot 
Brake cable Ø 1.8 mm x 220 cm (pear-shaped nipple)
Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Ø nipple: 3.5 mm · Ø nipple: 6 mm · Nipple length: 10 mm · Area of application: Standard · Ø Stranded wire: 1.8 mm · Cable length: 2200 mm · Nipple shape: Pears · Number of components: 1 pcs
EUR 2.85
EUR 2.50
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 28 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ball bearing closed: Yes
EUR 37.00
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Material: Steel · Surface: galvanized (blue) · Manufacturer: swiing® revival parts · Ø outside: 91 mm · Ø axle: 12 mm · Ø External brake pads: 80 mm · Total length: 187 mm · Ø screw holder: 6.5 mm · Ø bore: 12.2 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 8 mm · Brake lever length (lever length): 55 mm
EUR 83.60
swiing® revival rear brake anchor plate | Puch Maxi N
Material: Steel · Surface: galvanized (blue) · Manufacturer: swiing® revival parts · Ø outside: 92 mm · Ø axle: 12 mm · Ø External brake pads: 80 mm · Total length: 135 mm · Ø screw holder: 6.5 mm · Ø bore: 12.2 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 10 mm · Brake lever length (lever length): 68 mm
EUR 89.60
Magura set screw M6x34 mm lock nut SW10
Material: Brass · Manufacturer: Magura · Surface: nickel-plated · Total length: 34 mm · Slotted: No · Width across flats Screw: 8 mm · Ø cable holder: 3.05 mm · Ø Receptacle: 7.05 mm · Thread type: M6x1 (standard thread) · Width across flats nut: 10 mm · Thread length: 23 mm
EUR 3.00
Not in stock
swiing® revival wheel axle M12x1 x 185 rear (closed ball bearing) | Puch
Manufacturer: swiing® revival parts · Ø shaft: 11.95 mm · Material: Steel · Surface: galvanized (blue) · Total length: 185 mm · Shank length: 99 mm · Width across flats: 7 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 28 mm · Thread length: 52 mm
EUR 11.80
SKF 16101 2RS1 ball bearing 12/30/8
Bearing cage: Sheet steel cage ball-guided · Inner ring width: 8 mm · Manufacturer: SKF · Dust protection type: 2RS1 - NBR contact seal on both sides · Bearing clearance: CN (standard) · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Stock number: 16101 · Bearing type: Deep groove ball bearing · Ø inside: 12 mm · Width: 8 mm · Ø outside: 30 mm · Area of application: Standard · Ball bearing closed: Yes
EUR 19.50
Explore categories from Hub & axle
Moped fans also bought
GPO 38 mm cylinder head original | Puch Maxi S, N / X30 NS, NL, N-2AH
Material: Aluminum · Manufacturer: GPO · Surface: sandblasted · Area of application: Standard · Ø cylinder: 38 mm · Total length: 135 mm · Candle thread: short · Width: 125 mm · Height: 55 mm · Number of fixing points: 4 pcs · Hole pattern [mm]: 44 x 44 · Decompressor: No
EUR 39.30
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Material: Chrome steel (colloquially known as stainless steel) · Manufacturer: GPO · Surface: raw · Nipple length: 14 mm · Quantity: 36 pcs · Length from hook: 188 mm · Ø spoke head: 5.35 mm · Ø spoke: 2.9 mm · Nominal diameter (thread): 3.15 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Color: silver · Hook length: 9 mm · Hook angle: 95 ° · Thread length: 11 mm
EUR 65.70
swiing® ingenious wheel axle with bearing conversion kit spoke hub front | Puch
Material: Steel · Surface: galvanized (blue) · Manufacturer: swiing® ingenious parts · Ø outside: 29.02 mm · Total length: 165 mm · Ø inside: 12 mm · Thread type: MF12x1 (fine pitch thread) · Width across flats: 19 mm · Ø shaft: 11.95 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Shank length: 74.5 mm · Ball bearing closed: Yes · Thread length: 40.5 mm · Thread length: 50 mm
EUR 46.50
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Material: Steel · Surface: galvanized (blue) · Manufacturer: swiing® revival parts · Ø outside: 91 mm · Ø axle: 12 mm · Ø External brake pads: 80 mm · Total length: 187 mm · Ø screw holder: 6.5 mm · Ø bore: 12.2 mm · Ø shaft: 10 mm · Wide cam holder: 12 mm · Cranking (offset): 8 mm · Brake lever length (lever length): 55 mm
EUR 83.60
Collection only possible with online purchase and appointment.
