Complete set of 0.8 mm thick steel disc springs for the HRT SX50 KTM clutch on your Puch moped with an E50 engine.
The disc springs are of the highest quality and have a precisely defined spring rate, ensuring that each disc exerts the same pressure.
The pairs of spring washers are stacked with their arched sides facing each other over the spacer sleeve. Depending on your needs, you can stack more or fewer pairs to adjust the spring tension to the engine’s requirements.
As a basic setting for the initial installation, we recommend the following configuration of the spring stacks: ()()()()()()(,
with a total thickness of the 13 stacked disc springs of approximately 15.5 mm.
The package includes 48 disc springs.
Note: If you’re using the clutch continuously on the racetrack, you should opt for stainless steel disc springs due to the high heat generated. You can find these, along with all other clutch parts, in the accessories section.
A quality product from the Swiss manufacturer HR-TECHNIK.
| Manufacturer | HR-Technik |
| Material | Steel |
| Ø inside | 8.2 mm |
| Ø outside | 15 mm |
| Number of springs | 48 pcs |
| Thickness | 0.8 mm |
| Area of application | Racing, High End |
| Puch | E50 |
Accessories & related products
HRT screw set clutch hub KTM SX50 (strength 10.9) | Puch E50
Manufacturer: HR-Technik · Material: Steel · Surface: blackened · Thread type: M6x1 (standard thread) · Nominal diameter (thread): 6 mm · Drive: External hexagon · Screw head: Hexagon · Width across flats: 10 mm · Thread length: 25 mm · Number of components: 3 pcs
EUR 10.90
HRT disk spring set 0.8 mm clutch KTM SX50 Inox | Puch E50
Manufacturer: HR-Technik · Material: Chrome steel (colloquially known as stainless steel) · Number of springs: 48 pcs · Ø inside: 8.2 mm · Thickness: 0.8 mm · Ø outside: 15 mm · Area of application: High End · Area of application: Racing
EUR 61.40
Explore categories from Clutch
Moped fans also bought
Polini jet set (120 - 138) main jets long version CP, Keihin, Koso, PWK
Manufacturer: Polini · Component group Carburetor: Spraying · Material: Brass · Quantity: 10 pcs · Carburetor type: CP · Carburetor type: Coso · Carburetor type: Keihin · Carburetor type: PWK · Nozzle type: Main nozzle · Nozzle size: 120 · Nozzle size: 122 · Nozzle size: 124 · Nozzle size: 126 · Nozzle size: 128 · Nozzle size: 130 · Nozzle size: 132 · Nozzle size: 134 · Nozzle size: 136 · Nozzle size: 138 · Drive: External hexagon
EUR 49.10
66HEROES Exhaust bracket 75 mm flat Inox
Manufacturer: 66HEROES · Material: Chrome steel (colloquially known as stainless steel) · Surface: electropolished · Ø mounting hole: 8.3 mm · Ø mounting hole: 20 mm · Thickness: 4 mm · Number of fixing points: 2 pcs · Hole spacing: 75 mm · Total length: 106 mm
EUR 15.40
swiing® revival clutch plates (2 pcs.) | Sachs 50/2, 503 2AL/2BL (A3887)
Manufacturer: swiing® revival parts · Material: Composite materials · Material: Steel · Recording type: Interlocking · Number of slats: 2 pcs · Ø outside: 93.7 mm · Ø inside: 29.7 mm · Ø inside: 36 mm · Thickness: 3.3 mm · Area of application: Standard · Pony OEM number: A3887 · Sachs OEM no.: 0659 010 006
EUR 32.60
swiing® revival gasket gearbox cover engine 1 mm | Puch E50
Manufacturer: swiing® revival parts · Material: Sealing paper · Color: sand-colored · Ø inside: 106 mm · Ø outside: 116 mm · Thickness: 1 mm · Number of components: 1 pcs · Number of fixing points: 4 pcs · Alternative version of the Puch OEM number: 349.1.10.349.1
EUR 4.80
swiing® revival thrust washer set Ø 15 / 17 mm | Puch E50
Ø inside: 15 mm · Ø inside: 17 mm · Manufacturer: swiing® revival parts · Ø outside: 22 mm · Ø outside: 24 mm · Material: Steel · Surface: hardened & ground · Area of application: Standard · Thickness: 1.1 mm · Thickness: 1.3 mm · Thickness: 1.5 mm · Thickness: 1.7 mm
EUR 47.90
Polini CP 21 mm carburetor (hand choke) rubber flange
Manufacturer: Polini · Camouflaged: No · Component group Carburetor: Carburetor complete · Material: Aluminum · Carburetor type: CP · Nominal diameter: 21 mm · Ø Inside entrance: 42 mm · Ø Output inside: 22.5 mm · Ø Air filter connection: 47 mm · Ø fuel hose connection: 6 mm · Ø fuel hose connection: 7 mm · Mixed oil connection: Yes · Vacuum connection: Yes · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Nozzle block: 35-12 · Nozzle size: 100 · Size of secondary nozzle: 40 · Mounting type: Rubber sleeve · Total length: 71 mm · Width: 66 mm · Height: 132 mm · Area of application: Performance · Area of application: Racing · Area of application: Tuning
EUR 172.20
Working late? Evening hours on Thursday until 20:00
