BGS compressed air pin grinder 54,000 rpm (3 mm holder)

Autosol Aluminum Polish 75 ml

Manufacturer: Autosol · Material to be used: Aluminum · Contents [ml]: 75 ml · Area of application: Chemistry · Hazard warning: Causes serious eye irritation · Hazard warning: Causes skin irritation · Hazard warning: Harmful to aquatic organisms (with long-term effects) · Signal word: Attention · Hazard pictogram: GHS07 - Caution dangerous

Grinding stone set 10 pcs.

Drive shank Drill chuck: round · Ø drill chuck holder: 3 mm · Ø drill chuck holder: 6 mm · Number of components: 10 pcs · Area of application: Workshop accessories

Sanding/brush set 12 pcs.

Drive shank Drill chuck: round · Ø drill chuck holder: 3 mm · Number of components: 12 pcs · Material: Nylon · Area of application: Workshop accessories

Grinding compound valve 10 g

Manufacturer: Made in Germany · Area of application: Workshop accessories

BGS compressed air pneumatic filler 0 - 10 bar calibrated (with pressure gauge)

Manufacturer: BGS · Area of application: Workshop accessories · Total length: 400 mm

Plug nipple 300 female thread 1/4" (CH)

Area of application: Workshop accessories · Mounting thread [inch]: 1/4"

swiing® ingenious clutch springs reinforced (+20%) (Version 2.0) | Puch E50

Spring design: Pressure spring · Ø wire: 1.7 mm · Number of components: 3 pcs · Manufacturer: swiing® ingenious parts · Material: Spring steel · Color: blue · Surface: coated · Area of application: Tuning · Ø outside: 8.3 mm · Ø inside: 4.8 mm · Total length: 28 mm

Large outlet seal with metal ring

Place of use: Outlet · Material: Sealing carton · Material: Sheet metal (steel) · Reinforced: Yes · Ø outlet inside: 27 mm · Thickness: 2.1 mm · Ø screw holder: 6.3 mm · Hole spacing outlet: 42.5 mm · Area of application: Tuning

swiing® revival stud bolt inlet/outlet M6 x 30 mm (10.9 strength)

Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Diameter: 5.95 mm · Thread type: M6x1 (standard thread) · Total length: 30 mm · Thread length: 12 mm · Strength class: 10.9

swiing® revival engine revision set (new model) | Puch E50

Number of components: 7 pcs · Manufacturer: swiing® revival parts · Area of application: Tuning

Gas cable Ø 1.25 mm x 220 cm (cylindrical nipple) Bing

Ø Stranded wire: 1.25 mm · Cable length: 2200 mm · Nipple shape: Cylinder · Ø nipple: 3 mm · Number of components: 1 pcs · Nipple length: 5 mm · Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Area of application: Standard

NGK CR6 Racing ignition cable & plug High End red

Cable length: 1000 mm · Manufacturer: NGK · Material: Rubber · Color: red · Cable available: Yes · Suppressed: Yes · Resistance: 5000 Ω · Component group Carburetor: Ignition cable · Component group Carburetor: Spark plug connector · Ø cable: 7 mm

swiing® revival screw set Motor E50 Inox | Puch Maxi

Manufacturer: swiing® revival parts · Material: Chrome steel (known as Nirosta®) · Surface: stainless

Shaft seal NBR 16/25/7 A Kickstarter | Puch E50

Temperature resistance (min.): -30 - 100 °C · Simmering type: A - With rubberized outer part / one sealing lip. · Manufacturer: Puch · Material: NBR · Surface: rubberized · Ø outside: 25 mm · Width: 7 mm · Ø inside: 16 mm

BGS Diamond grinder set small 20 pcs.

Drive shank Drill chuck: round · Ø drill chuck holder: 3 mm · Number of components: 20 pcs · Manufacturer: BGS · Material: Diamond · Area of application: Workshop accessories

Milling cutter set tungsten carbide 10 pcs.

Drive shank Drill chuck: round · Ø drill chuck holder: 3 mm · Number of components: 10 pcs · Material: Tungsten carbide · Area of application: Workshop accessories · Total length: 43 mm · Total length: 50 mm